**Featured Image:**
The 2015 Subaru Impreza Sedan is a compact car that offers a comfortable ride and plenty of features. However, if you’re looking to upgrade the car’s camera, you’ll need to remove the old one first. This can be a tricky task, but with the right tools and instructions, it’s definitely doable. In this article, we’ll walk you through the steps on how to remove the old camera from your 2015 Subaru Impreza Sedan. We’ll also provide some tips on how to avoid damaging the car in the process.
Before you begin, it’s important to gather all of the necessary tools. You’ll need a Phillips head screwdriver, a flat head screwdriver, and a trim removal tool. You may also want to wear gloves to protect your hands from getting cut. Once you have all of your tools, you can begin the removal process. First, you’ll need to remove the trim panel around the camera. To do this, insert the flat head screwdriver into the gap between the trim panel and the dashboard. Gently pry the trim panel loose, being careful not to break any of the clips. Once the trim panel is loose, you can remove it by hand.
Safely Accessing the Camera
To successfully remove the old camera from your 2015 Subaru Impreza Sedan, it’s crucial to take proper safety precautions. Here’s a detailed guide to assist you:
1. Park and Engage the Parking Brake: Ensure the vehicle is parked on a level, stable surface. Engage the parking brake to prevent the car from rolling while working.
2. Disconnect the Battery: Locate the negative battery terminal under the hood. Using a wrench, loosen the nut and carefully disconnect the negative cable. This step is essential to prevent any electrical short circuits.
3. Remove the Tail Light Assembly: Open the trunk and locate the rear tail light assembly on the affected side. Gently pry around the edges of the assembly using a plastic pry tool or a flat-head screwdriver, taking care not to damage the paint or trim. Once the assembly is loose, carefully pull it away from the vehicle.
4. Unplug the Electrical Connectors: Inside the tail light assembly, locate the electrical connectors for the camera and gently unplug them. Be cautious not to damage the wiring or connectors.
5. Support the License Plate Light: Before removing the camera, support the license plate light with a small wedge or a piece of cardboard to prevent it from falling out.
Unplugging the Wiring Harness
Before you can remove the old camera, you’ll need to unplug the wiring harness. To do this, locate the harness connector on the back of the camera. It’s usually a black or gray connector with several wires coming out of it.
Once you’ve found the connector, press on the release tab and pull the connector straight out. Be careful not to damage the wires.
Here’s a table to help you identify the wires in the wiring harness:
| Wire Color | Function |
|---|---|
| Black | Ground |
| Red | Power |
| Yellow | Video signal |
Detaching the Camera Assembly
To detach the camera assembly, carefully follow these steps:
1. Disconnect the Negative Battery Terminal
Using a wrench, loosen the negative battery terminal. This will cut off the power supply to the camera, preventing any potential electrical shocks during the removal process.
2. Access the Camera Assembly
Locate the camera assembly on the rear of the vehicle and remove the trim panel surrounding it. This will expose the assembly, allowing you to detach it.
3. Unplug the Camera Connectors
Identify the electrical connectors connected to the camera assembly. Using a small flat-head screwdriver or trim removal tool, gently pry the connectors loose. Disconnect all connectors by pressing on the release tabs and pulling them straight out. Refer to the table below for the location of specific connectors:
| Connector | Location |
|---|---|
| Main Camera Connector | Top of the camera assembly |
| Video Signal Cable Connector | Bottom of the camera assembly |
| Power Supply Connector | Left side of the camera assembly |
4. Remove the Camera Assembly
Once all connectors are detached, carefully remove the camera assembly from the vehicle by gently wiggling it and pulling it straight out. Ensure not to damage the wires or connectors during this process.
Removing the Old Camera Module
1. Disconnect the negative terminal of the battery.
2. Remove the trunk lid liner.
3. Locate the camera module. It is located in the center of the trunk lid, behind the license plate.
4. Disconnect the electrical connector from the camera module.
a. Use a small flathead screwdriver to pry the locking tab on the electrical connector.
b. Pull the electrical connector straight out of the camera module.
c. Be careful not to damage the electrical connector or the camera module.
d. Note: The electrical connector may be difficult to remove. If you are having difficulty, you can use a pair of pliers to gently pull the connector out.
5. Remove the two screws that secure the camera module to the trunk lid.
6. Carefully pull the camera module straight out of the trunk lid.
7. Disconnect the video cable from the camera module.
8. Remove the old camera module from the vehicle.
Disconnecting the Wiring Harness
Before you can remove the old camera, you need to disconnect the wiring harness. To do this, follow these steps:
- Locate the wiring harness that is connected to the camera.
- Use a flathead screwdriver to gently pry the locking tab on the harness connector.
- Pull the harness connector straight out of the camera.
- Repeat steps 2 and 3 for the other harness connector.
- Slowly pull the wiring harness away from the camera, taking care not to damage the wires.
| Step | Description |
|---|---|
| 1 | Locate the wiring harness that is connected to the camera. |
| 2 | Use a flathead screwdriver to gently pry the locking tab on the harness connector. |
| 3 | Pull the harness connector straight out of the camera. |
| 4 | Repeat steps 2 and 3 for the other harness connector. |
| 5 | Slowly pull the wiring harness away from the camera, taking care not to damage the wires. This step may require some patience and wiggling to free the harness from any clips or tight spots. |
Releasing the Camera Bracket
To release the camera bracket, you will need a 10mm socket or wrench.
- Locate the two 10mm bolts that hold the camera bracket in place. The bolts are located on the top and bottom of the bracket.
- Using the 10mm socket or wrench, loosen the bolts.
- Once the bolts are loose, you can remove the camera bracket from the vehicle.
Detailed Instructions for Step 6
Carefully lift the camera bracket up and away from the vehicle. Be careful not to damage the camera or the bracket.
Disconnect the electrical connector from the back of the camera. The electrical connector is located on the bottom of the camera.
To disconnect the electrical connector, press down on the tab on the side of the connector and pull the connector straight out.
Once the electrical connector is disconnected, you can remove the camera from the bracket.
To remove the camera from the bracket, press down on the tabs on the sides of the camera and pull the camera straight out of the bracket.
Unbolting the Camera Mount
To unbolt the camera mount, you will need to locate the three bolts that secure it to the vehicle’s body. These bolts are typically located at the top, bottom, and side of the mount. Once you have located the bolts, use a socket wrench to loosen and remove them. Be careful not to drop the bolts or the camera mount.
Once the bolts have been removed, you can gently pull the camera mount away from the vehicle’s body. Be careful not to damage the camera or the mount.
Here is a more detailed guide to unbolting the camera mount:
| Step | Description |
|---|---|
| 1 | Locate the three bolts that secure the camera mount to the vehicle’s body. |
| 2 | Use a socket wrench to loosen and remove the bolts. |
| 3 | Gently pull the camera mount away from the vehicle’s body. |
Replacing the Camera Module
8. Disassemble the Camera Module:
| Step | Description |
|---|---|
| 8a | Locate and remove the two retaining screws that hold the lens assembly in place. Carefully separate the lens assembly from the camera module, taking care not to damage the delicate components inside. |
| 8b | Unplug the electrical connector that connects the lens assembly to the camera module. Gently pull the connector straight out of its socket. |
| 8c | Locate and remove the four retaining screws that secure the circuit board to the camera module. Carefully lift the circuit board out of the module, using a prying tool if necessary. |
| 8d | Unplug any remaining electrical connectors that may be attached to the circuit board. Note the location of each connector for proper reassembly. |
| 8e | Carefully remove the old camera sensor from the circuit board. It may be held in place by additional screws or clips. |
Reconnecting the Wiring Harness
9. Reconnect the Camera Harness
Finally, it’s time to reconnect the camera’s wiring harness. This is a sensitive component, so it’s essential to handle it with care.
Locate the camera’s wiring harness, which will be a small, black connector. Insert the connector into the corresponding port on the new camera, ensuring it’s securely attached.
Double-check the connection by gently tugging on the harness. If it feels loose, reinsert it and ensure a snug fit.
Once the camera harness is reconnected, you can proceed to mount the camera onto the vehicle.
9.a. Step-by-Step Guide to Reconnecting Camera Harness
| Step | Action |
|---|---|
| 1 | Locate the camera’s wiring harness (small, black connector). |
| 2 | Insert the harness into the port on the new camera. |
| 3 | Securely attach the connector. |
| 4 | Tug gently on the harness to ensure it’s not loose. |
| 5 | Mount the camera onto the vehicle. |
Reinstalling the Camera Assembly
Step 1: Align the Camera Module
Position the camera module carefully into the housing. Ensure the module is correctly aligned with the mounting points.
Step 2: Secure the Camera Module
Use the provided mounting screws or bolts to securely fasten the camera module in place. Tighten the screws or bolts to the specified torque.
Step 3: Connect the Wiring Harness
Locate and connect the wiring harness to the camera module. Ensure the harness is fully engaged and locked into place.
Step 4: Test the Camera
Start the engine and engage reverse gear. Verify that the camera is functioning correctly and displays the rearview image on the dashboard screen.
Step 5: Adjust Camera Angle (Optional)
If necessary, adjust the camera angle for optimal viewing. Use the mounting screws or bolts to loosen or tighten the camera, then slide it up or down slightly.
Step 6: Reattach the Trim Panel
Align and snap the trim panel back into place around the camera housing. Press on the edges of the panel to ensure a secure fit.
Step 7: Final Check
Thoroughly inspect the camera and surrounding area to ensure proper installation. Check for any loose wires, damaged components, or alignment issues.
Step 8: Calibration (Optional)
Some camera systems may require calibration after installation. Refer to the vehicle owner’s manual for specific calibration instructions, if applicable.
Step 9: Data Reset (Optional)
In certain cases, it may be necessary to reset the vehicle’s computer system after camera installation to ensure optimal functionality.
Step 10: Troubleshooting
If you encounter any issues with the camera installation or functionality, refer to the following troubleshooting table for possible solutions:
| Issue | Possible Solution |
|---|---|
| No Camera Image | – Check wiring harness connections – Verify camera power supply – Reset vehicle’s computer system |
| Distorted Camera Image | – Check camera lens for damage or debris – Adjust camera angle for optimal viewing – Calibrate the camera system |
| Camera Not Detected | – Check if the camera is compatible with the vehicle – Inspect the wiring harness for any breaks or shorts – Clean the camera connections |
2015 Subaru Impreza Sedan: How to Remove Old Camera
Here’s how you can remove the old camera from your 2015 Subaru Impreza Sedan:
- Open the trunk of your Impreza and locate the camera. It’ll be mounted on the inside of the trunk lid, near the center.
- Use a screwdriver to remove the two screws that hold the camera in place.
- Disconnect the electrical connector from the back of the camera.
- Remove the camera from the trunk lid.
People Also Ask About 2015 Subaru Impreza Sedan: How to Remove Old Camera
What tools do I need to remove the old camera from my 2015 Subaru Impreza Sedan?
You’ll need a screwdriver to remove the two screws that hold the camera in place.
Where is the camera located on a 2015 Subaru Impreza Sedan?
The camera is mounted on the inside of the trunk lid, near the center.
Can I remove the old camera myself?
Yes, you can remove the old camera yourself. The process is relatively simple and only requires a few minutes of your time.
