The Honda Silverwing is a maxi-scooter that was first introduced in 2001. It has been praised for its comfort, performance, and fuel efficiency. However, one common complaint about the Silverwing is that it can be difficult to access the fuel pump. This can be a problem if the fuel pump needs to be replaced or repaired.
In this article, we will show you how to get to the fuel pump on a Honda Silverwing. We will provide step-by-step instructions and photos to help you complete the task. We will also provide some tips on how to avoid common mistakes.
Before you begin, it is important to gather the tools and materials that you will need. You will need a socket wrench, a Phillips screwdriver, and a flat-blade screwdriver. You will also need a new fuel pump, if you are replacing the old one. Once you have gathered the necessary tools and materials, you can begin the process of removing the fuel pump.
Identifying the Location of the Fuel Pump
The fuel pump in a Honda Silverwing is an essential component that provides the engine with a continuous supply of fuel. It is located inside the fuel tank and is submerged in the gasoline, which helps to keep it cool and lubricated. To access the fuel pump, you will need to remove the fuel tank from the motorcycle.
Here are the steps on how to get to the fuel pump:
| Step | Description |
|---|---|
| 1 | Remove the seat. |
| 2 | Disconnect the fuel line from the fuel pump. |
| 3 | Remove the bolts that hold the fuel pump in place. |
| 4 | Pull the fuel pump out of the fuel tank. |
Once you have removed the fuel pump, you can inspect it for any damage or wear. If the fuel pump is damaged, it will need to be replaced.
Preparing for Fuel Pump Access
Before you can access the fuel pump, you’ll need to take a few preparatory steps. These steps will help you to safely and successfully complete the repair.
Gather your tools and materials
You will need the following tools and materials to complete this repair:
- Socket wrench set
- Screwdriver set
- Fuel line pliers
- Fuel filter
- Fuel pump
- Gasoline
Safety considerations
When working on your vehicle’s fuel system, it is important to take safety precautions to avoid serious injury or damage. The following safety considerations should be observed:
- Work in a well-ventilated area.
- Do not smoke or use open flames near the vehicle.
- Wear safety glasses and gloves.
- Disconnect the negative battery terminal before starting work.
- Relieve fuel system pressure before disconnecting any fuel lines.
Locate the fuel pump
The fuel pump is located in the fuel tank. To access the fuel pump, you will need to remove the fuel tank from the vehicle. The fuel tank is typically located under the rear of the vehicle. Once you have removed the fuel tank, you will be able to access the fuel pump.
Removing the Seat and Fairings
To access the fuel pump, you’ll need to remove the seat and fairings. Here’s how:
1. Remove the Seat
Locate the seat release lever under the rear of the seat. Pull the lever towards you and lift the seat off the bike.
2. Remove the Left Fairing
Locate the fasteners holding the left fairing in place. Typically, you’ll find two screws at the front, two at the back, and one or two along the side. Remove all the fasteners and carefully pull the fairing away from the bike.
3. Remove the Right Fairing
Repeat steps for removing the left fairing for the right side, paying attention to detaching any additional wires or components that may be connected to the right fairing, such as the turn signal connector, the fuel line connector, or the exhaust pipe hanger.
| Component | Location | Removal Type |
|---|---|---|
| Turn Signal Connector | Behind the fairing | Disconnect wire |
| Fuel Line Connector | Near the fuel tank | Loosen clamp and detach |
| Exhaust Pipe Hanger | Bottom of the fairing | Unbolt hanger |
Disconnecting Electrical Components
Before disconnecting any electrical components, it is important to disconnect the negative battery terminal to prevent electrical shocks or damage to the system. Here are the steps involved in disconnecting the electrical components:
1. Locate the Fuel Pump Electrical Connector
The fuel pump electrical connector is typically located near the fuel tank or fuel pump. It is a large, waterproof connector with several wires running to it.
2. Disconnect the Fuel Pump Electrical Connector
To disconnect the fuel pump electrical connector, simply press on the release tab and pull the connector apart. Do not pull on the wires, as this can damage them.
3. Disconnect the Fuel Pump Ground Wire (Optional)
In some cases, there may be a separate ground wire connected to the fuel pump. If there is a ground wire, disconnect it by loosening the bolt or nut that secures it.
4. Detaching the Fuel Pump Assembly from the Fuel Tank
Once the electrical components are disconnected, you can detach the fuel pump assembly from the fuel tank. This may require removing bolts, nuts, or clips that secure the assembly to the tank.
To provide further guidance on detaching the fuel pump assembly from the fuel tank, consider the following table:
| Vehicle Model | Detachment Instructions |
|---|---|
| Honda Silverwing 600 (2002-2008) | Remove the four bolts that secure the fuel pump assembly to the fuel tank. Gently lift the assembly straight up to detach it. |
| Honda Silverwing 400 (2009-2018) | Disconnect the quick-release fuel line connectors. Remove the two bolts that secure the fuel pump assembly to the fuel tank. Carefully lift the assembly straight up to detach it. |
Draining Fuel from the Fuel Line
Once the fuel line is disconnected from the fuel pump, you can proceed to drain the fuel from the line. This is done to prevent fuel from spilling or leaking out during the installation of the new fuel pump.
To drain the fuel from the fuel line, follow these steps:
- Place a suitable container underneath the fuel line.
- Open the fuel line by either disconnecting the quick-disconnect connector or loosening the fuel line clamp.
- Allow the fuel to drain into the container.
- Once the fuel has stopped flowing, reconnect the fuel line or tighten the fuel line clamp.
- Dispose or recycle the fuel drained from the fuel line according to your local regulations.
Table: Fuel Disposal
| Method | Instructions |
|---|---|
| Dispose of fuel at a waste collection center | Contact your local waste management authority for instructions on how to dispose of fuel safely and legally. |
| Recycle fuel | Locate a recycling center that accepts fuel. Check online or with your local authorities for options. |
| Use fuel for other purposes (e.g., cleaning parts) | Filter the fuel through a fine-mesh filter to remove any impurities. Use the filtered fuel for cleaning or other non-automotive purposes. |
Removing the Fuel Tank
Before accessing the fuel pump, you need to remove the fuel tank. Here’s how:
- Place the scooter on a stable surface and engage the parking brake.
- Remove the seat by lifting it and unhooking the latch.
- Locate the fuel line and disconnect it from the tank by pressing the release clip.
- Disconnect the electrical connector for the fuel level sensor.
- Unbolt the bolts securing the fuel tank to the frame.
- Carefully lift the fuel tank and place it aside.
Note:
Take precautions when handling fuel as it is flammable. Ensure good ventilation and avoid smoking or using open flames near the work area.
| Tools Required | Description |
|---|---|
| Socket Wrench | For removing bolts securing the fuel tank |
| Phillips Screwdriver | For disconnecting the electrical connector |
| Fuel Line Disconnect Tool | For releasing the fuel line clip |
Accessing the Fuel Pump Module
**1. Remove the seat.**
**2. Remove the battery.**
**3. Remove the battery box.**
**4. Remove the air cleaner box.**
**5. Remove the fuel tank.**
**6. Remove the fuel pump cover.**
**7. Disconnect the fuel lines and electrical connector.**
To disconnect the fuel lines, use a pair of pliers to squeeze the release tabs on the fuel line connectors and pull the fuel lines off the fuel pump. To disconnect the electrical connector, use a small screwdriver to release the lock tab on the connector and pull the connector off the fuel pump.
**8. Remove the fuel pump.**
The fuel pump is held in place by two screws. Remove the screws and lift the fuel pump out of the fuel tank.
**9. Inspect the fuel pump and replace it if necessary.**
Inspect the fuel pump for any damage or wear. If the fuel pump is damaged or worn, it must be replaced.
**10. Reinstall the fuel pump.**
To reinstall the fuel pump, reverse the steps in the removal procedure. Be sure to tighten the screws that hold the fuel pump in place.
**11. Reinstall the fuel tank.**
**12. Reinstall the air cleaner box.**
**13. Reinstall the battery box.**
**14. Reinstall the battery.**
**15. Reinstall the seat.**
How to Get to the Fuel Pump
If your Honda Silverwing is experiencing fuel-related issues, you may need to replace the fuel pump. Here’s a step-by-step guide on how to get to the fuel pump:
1. Safety First
Before you begin, ensure the Silverwing is parked on a level surface, the engine is off, and the ignition key is removed.
2. Remove the Seat
Locate the seat lock, typically located at the front or rear of the seat. Insert the key and turn it to release the seat. Lift the seat off the Silverwing.
3. Disconnect the Battery
Use a wrench to loosen the negative battery terminal and disconnect the battery.
4. Remove the Fuel Tank
Locate the fuel tank bolts, usually found on the sides of the tank. Remove the bolts and carefully lift the fuel tank off the frame.
5. Remove the Fuel Pump Cover
Find the fuel pump cover, typically secured by bolts or screws. Remove the cover to expose the fuel pump.
6. Disconnect the Fuel Lines
Carefully disconnect the fuel lines connected to the fuel pump. Use a fuel line removal tool for safety.
7. Remove the Fuel Pump
Locate the fuel pump bolts or screws. Remove them and gently pull the fuel pump out of the assembly.
8. Inspect and Replace the Fuel Pump
Inspect the fuel pump for damage or wear. If necessary, replace the fuel pump with a new one. Ensure the correct fitment and secure it with the bolts or screws.
| Part | Torque |
|---|---|
| Fuel Pump Bolts | 8-10 Nm |
9. Reconnect
Connect the fuel lines to the new fuel pump. Reinstall the fuel pump cover and fuel tank.
10. Reconnect the Battery
Reconnect the negative battery terminal and tighten it securely.
11. Install the Seat
Place the seat on the Silverwing and engage the seat lock.
12. Start the Engine
Insert the ignition key and start the engine. Check for any fuel leaks and ensure the engine runs smoothly.
Reinstalling Components in Reverse Order
9. Reinstall the Fuel Pump and Filter
a. Align the fuel pump with the fuel tank and carefully insert it into the opening.
b. Secure the fuel pump using the mounting bolts and tighten them to the specified torque.
c. Slide the fuel filter onto the fuel pump outlet and secure it with the clamp.
d. Reconnect the fuel line to the fuel pump and tighten the clamp.
e. Connect the electrical connector to the fuel pump.
f. Install the fuel pump cover and secure it with the bolts.
10. Reinstall the Filler Cap
a. Replace the filler cap and tighten it securely.
11. Reinstall the Battery
a. Connect the positive battery terminal first and then the negative terminal.
b. Tighten the battery terminals to the specified torque.
12. Reinstall the Seat
a. Align the seat with the frame and slide it into place.
b. Secure the seat with the seat bolt.
13. Check for Leaks
a. Start the engine and let it idle.
b. Check for any fuel leaks from the fuel pump, fuel filter, or fuel line.
c. If any leaks are found, tighten the connections or replace the damaged components.
Priming the Fuel System
After replacing your fuel pump, you need to prime the fuel system to ensure that there is fuel flowing to the engine. Here are the steps involved in priming the fuel system:
If you have any leaks or if the engine does not start after priming, you may need to repeat these steps or consult with a professional mechanic.
How To Get To The Fuel Pump On A Honda Silverwing
The fuel pump on a Honda Silverwing is located in the fuel tank. To access the fuel pump, you will need to remove the fuel tank from the motorcycle.
To remove the fuel tank, follow these steps:
- Turn off the fuel petcock.
- Disconnect the fuel line from the fuel tank.
- Remove the bolts that secure the fuel tank to the frame.
- Carefully lift the fuel tank off of the motorcycle.
Once the fuel tank is removed, you will need to remove the fuel pump from the fuel tank. To remove the fuel pump, follow these steps:
- Disconnect the electrical connector from the fuel pump.
- Remove the bolts that secure the fuel pump to the fuel tank.
- Carefully lift the fuel pump out of the fuel tank.
Once the fuel pump is removed, you can replace it with a new fuel pump. To install a new fuel pump, follow these steps:
- Insert the new fuel pump into the fuel tank.
- Secure the fuel pump to the fuel tank with the bolts.
- Connect the electrical connector to the fuel pump.
- Reinstall the fuel tank on the motorcycle.
- Connect the fuel line to the fuel tank.
- Turn on the fuel petcock.
People Also Ask About Honda Silverwing How To Get To The Fuel Pump
What are the symptoms of a bad fuel pump on a Honda Silverwing?
The symptoms of a bad fuel pump on a Honda Silverwing can include:
- Difficulty starting the motorcycle
- Engine stalling
- Loss of power
- Decreased gas mileage
How much does it cost to replace a fuel pump on a Honda Silverwing?
The cost to replace a fuel pump on a Honda Silverwing can vary depending on the year and model of the motorcycle. The average cost to replace a fuel pump on a Honda Silverwing is between $200 and $400.
How long does it take to replace a fuel pump on a Honda Silverwing?
It takes about 1-2 hours to replace a fuel pump on a Honda Silverwing.
