If your LG Model WT1101CW washing machine isn’t draining properly, you may need to remove and clean the drain pump. It is located at the bottom of the washing machine, and it is responsible for pumping the water out of the tub. Here is a step-by-step guide on how to remove the drain pump on your LG Model WT1101CW washing machine. However, if you’re not comfortable doing this yourself, call a qualified appliance repair technician.
Before you begin, you will need to gather a few tools: a Phillips head screwdriver, a flat head screwdriver, and a pair of pliers. You will also need a bucket to catch the water that will drain from the pump when you remove it. First, unplug the washing machine from the power outlet. Next, turn off the water supply to the washing machine. Then, place the bucket under the drain pump to catch the water that will drain out. Finally, use the Phillips head screwdriver to remove the screws that hold the drain pump in place.
Once you have removed the screws, use the flat head screwdriver to pry the drain pump loose from the washing machine. Be careful not to damage the drain pump or the surrounding components. Once the drain pump is loose, use the pliers to disconnect the hoses that are connected to it. Finally, lift the drain pump out of the washing machine. Now that you have removed the drain pump, you can clean it. To do this, use a damp cloth to wipe away any dirt or debris that has accumulated on the pump. You can also use a small brush to clean the inside of the pump. Once the pump is clean, reassemble it in the reverse order that you removed it.
Locating the Drain Pump
The drain pump is a vital component of your LG Model WT1101CW washing machine, responsible for expelling water from the tub during the spin cycle. If your washing machine is not draining properly, a faulty drain pump could be the culprit.
Locating the drain pump can vary depending on the specific model of your washing machine. However, in general, here are the steps to follow:
- Unplug the washing machine from the electrical outlet for safety reasons.
- Turn off the water supply valves connected to the washing machine.
- Tilt the washing machine back slightly to access the bottom of the unit.
- Locate the drain pump, which is typically situated at the front or bottom of the washing machine. It may be covered by a plastic panel that needs to be removed.
- Disconnect the hoses and wires connected to the drain pump. Be sure to note how they are connected for easy reassembly later.
- Remove the bolts or screws that secure the drain pump to the washing machine.
- Carefully pull the drain pump out of its housing. Inspect the pump for any damage or debris that may be causing it to malfunction.
Removing the Drain Hose
Locate the drain hose at the back of the washer, typically concealed behind a small access panel. Open the panel to expose the hose.
Disconnect the drain hose from the drain pump by gently pulling it away. A clamp or fastener may secure the hose, so be cautious when detaching it.
Pull the drain hose completely out of the washer, ensuring to drain any remaining water into a suitable container.
Optional Steps for Stubborn Hose Removal
If the drain hose is tightly stuck or clogged, consider these additional steps:
| Issue | Solution |
|---|---|
| Stubborn clamp | Use pliers to carefully loosen the clamp without damaging the hose. |
| Clogged hose | Clear debris by running a thin wire or brush through the hose and flushing with water. |
| Damaged hose | Replace the damaged section of the hose with a new one of the same size and material. |
Inspecting the Impeller
Once you have removed the drain pump, it is crucial to inspect the impeller for any damage or blockage. The impeller is a critical component of the drain pump responsible for spinning and draining water away from the washing machine. If the impeller is damaged or blocked, it can compromise the efficiency of the drain pump and lead to further issues.
To thoroughly inspect the impeller:
- Carefully remove the impeller from the drain pump housing.
- Examine the impeller for any cracks, breaks, or deformities. Even minor damage can affect its functionality.
- Check for any foreign objects or debris stuck in the impeller blades or the housing. These obstructions can block the smooth flow of water and hinder the impeller’s rotation.
- Inspect the impeller shaft for any signs of wear or corrosion. Excessive friction or rust can lead to difficulty in spinning and eventual failure.
- If visible damage or blockage is present, the impeller may need to be replaced or cleaned thoroughly.
- Always use genuine LG parts when replacing the impeller to ensure optimal performance and safety.
Regular inspection and maintenance of the impeller are essential for ensuring the longevity and proper functioning of your LG washing machine.
Reinstalling the Drain Pump
8. Replace the Screw
Locate the screw that holds the drain pump in place. It is typically located at the bottom of the pump. Align the screw with the hole in the mounting bracket and tighten it securely using a screwdriver. To ensure a secure fit, gently tug on the pump once screwed to confirm it is tightly in place.
9. Reconnect the Wiring
Locate the electrical connector for the drain pump. It is usually a small, plastic connector with two or three wires. Align the connector with the corresponding plug on the drain pump and push it firmly until it clicks into place. Double-check that the connector is secure and the wires are not loose or exposed.
10. Reinstall the Kick Panel
Lift the kick panel back into place, aligning it with the bottom of the washer cabinet. Push the kick panel firmly into position until it snaps into place. Ensure that the drain pump is not obstructed by the kick panel and that the panel covers the pump completely.
How to Remove Drain Pump on LG Model WT1101CW
Tools you’ll need:
- Phillips head screwdriver
- Flat head screwdriver
- Bucket or bowl
Instructions:
- Unplug the washer from the electrical outlet.
- Turn off the water supply to the washer.
- Open the washer door and remove the clothes.
- Locate the drain pump at the bottom of the washer. It is usually located on the right side.
- Disconnect the hoses from the drain pump.
- Remove the screws that hold the drain pump in place.
- Pull the drain pump out of the washer.
- Clean the drain pump and replace it if necessary.
- Reassemble the washer in the reverse order.
People Also Ask
How do I know if my LG Washer Drain Pump is bad?
There are a few signs that your LG washer drain pump may be bad:
- Your washer is not draining properly.
- Your washer is making a loud noise when it is draining.
- Your washer is leaking water from the bottom.
Can I replace the drain pump on my LG Washer myself?
Yes, you can replace the drain pump on your LG washer yourself. However, it is important to note that this is a difficult repair and should only be attempted by someone with experience in appliance repair.
