Preparation: Tools and Materials Required
Essential Tools:
- Precision screwdriver (small Philips head): For removing and replacing the Geek Bar Pulse’s top cap and mouthpiece.
- Disposable rubber gloves: To protect your hands from e-liquid remnants and potential spills.
Materials:
- Geek Bar Pulse disposable vape: The device you intend to refill.
- E-liquid of your choice: Compatible with the Geek Bar Pulse’s recommended e-liquid viscosity.
- Syringe with needle: A precision syringe with a fine needle tip is essential for injecting e-liquid into the refill port.
- Paper towels or tissues: For wiping up any spills or excess e-liquid.
Optional Materials:
- Tweezer: For carefully removing the mouthpiece if it is not easily removable by hand.
- Small funnel: For ease of pouring e-liquid into the syringe from the bottle.
Technical Specifications:
| Component | Specifications |
|---|---|
| Syringe Capacity | 1-2ml |
| Needle Gauge | 18-22G |
| E-Liquid Viscosity | 50-60VG/40-50PG |
Locating the Refill Port
The Geek Bar Pulse recharge port is conveniently located at the device’s bottom. To access it, you will need to remove the disposable base by gently detaching it from the rechargeable battery section.
Here’s a step-by-step guide to finding the refill port:
- Grip the disposable base and gently pull it downward to separate it from the battery section.
- Flip the disposable base upside down to reveal the bottom side.
- Locate the small circular opening on the center of the bottom side. This is the refill port.
The refill port is typically covered by a silicone plug. Remove the plug to access the port and prepare for refilling your Geek Bar Pulse.
Removing the Mouthpiece
Assess the Mouthpiece: Before attempting to remove the mouthpiece, thoroughly inspect it to identify any protruding tabs or notches that may require specific handling.
Locate the Release Mechanism: Carefully examine the base of the mouthpiece where it connects to the device. Identify any apparent buttons, levers, or sliding mechanisms designed to release the mouthpiece.
Apply Gentle Pressure: Once the release mechanism is identified, gently and firmly press or slide it in the designated direction. If there is resistance, avoid excessive force as it could damage the mouthpiece or device.
| Release Mechanism Type | Application Method |
|---|---|
| Push Button | Press the button and simultaneously pull the mouthpiece upward. |
| Sliding Lever | Slide the lever in the indicated direction while gently pulling the mouthpiece. |
Filling the Tank with E-Liquid
Materials Needed
- Geek Bar Pulse
- E-liquid bottle with needle tip
- Tissue or paper towel
Steps
- Remove the mouthpiece. Gently grasp the mouthpiece and pull it straight up to detach it from the device.
- Locate the fill port. The fill port is a small hole on the side of the device, typically near the bottom.
- Insert the needle tip. Carefully insert the needle tip into the fill port at a slight angle. Avoid pushing too far in to prevent damage to the device.
- Fill the tank slowly. Squeeze the e-liquid bottle to dispense the liquid into the tank. Fill it to the top, but avoid overfilling.
Tips for Filling the Tank
– Hold the device upright to prevent spills.
– Fill the tank slowly to allow the e-liquid to absorb into the coil.
– Avoid getting e-liquid on the device or mouthpiece, as this can cause leakage.
– If you do spill e-liquid, use a tissue or paper towel to wipe it up immediately.
Materials Required
Here is every item you may need:
- Geek Bar Pulse device
- Mouthpiece (from the original Geek Bar Pulse packaging)
Steps
1. Locate the Mouthpiece
Find the spare mouthpiece that came with the original Geek Bar Pulse packaging.
2. Align the Mouthpiece
Hold the mouthpiece and align it with the top portion of the device.
3. Insert the Mouthpiece
Apply gentle pressure and push the mouthpiece into the device until it fits snugly.
4. Adjust the Mouthpiece
Once inserted, adjust the mouthpiece so that the airflow holes are properly aligned.
5. Reattach the Coil
Locate the small coil inside the mouthpiece and gently reinsert it into the port on the top of the device. Ensure that the coil is pushed in far enough to make contact but not so far that it blocks airflow. To guide you while reattaching the coil, you can refer to the diagram below.
Diagram of Coil Reattachment:
| Coil Port | Coil |
|---|---|
 |
 |
6. Verify Connection
Take a few short puffs on the device to verify that the coil is properly reattached and that there is proper airflow.
Priming the Coil
Priming the coil is a crucial step to ensure the proper functioning of your Geek Bar Pulse and prevent dry hits. Follow these steps to prime the coil effectively:
- Remove the mouthpiece from the device.
- Locate the rubber plug on the bottom of the device.
- Use a paperclip or similar tool to remove the rubber plug.
- You will see a small hole leading to the coil.
- Tilt the device slightly and drip 2-3 drops of e-liquid into the hole.
- Replace the rubber plug and the mouthpiece.
Tips for Priming the Coil
Use high-quality e-liquids with a VG/PG ratio of 50/50 or 60/40.
Drip the e-liquid slowly and directly onto the coil.
Wait a few minutes for the e-liquid to soak into the coil.
By priming the coil, you ensure that it is fully saturated with e-liquid, which will prevent burning and deliver a smooth vaping experience.
Proper Disposal of Empty Cartridge
Once your Geek Bar Pulse cartridge is empty, it is crucial to dispose of it responsibly. Improper disposal can harm the environment and pose risks to wildlife. Here’s a step-by-step guide to properly dispose of an empty cartridge:
1. Remove the Cartridge
Gently remove the empty cartridge from the Geek Bar Pulse device.
2. Separate Components
If possible, separate the metal components from the plastic parts. This will make recycling easier.
3. Check Local Regulations
Check with your local waste management authority to determine the appropriate disposal methods in your area.
4. Dispose in E-Waste Bin
Look for designated e-waste bins or drop-off points where you can dispose of the empty cartridge and any other electronic waste.
5. Recycle Metal Components
If you separated the metal components, recycle them at a local scrap metal collection facility.
6. Discard Plastic Parts
Dispose of the plastic parts in the regular trash, ensuring they are securely sealed in a plastic bag to prevent litter.
7. Environmental Impact
Improper disposal of empty Geek Bar Pulse cartridges can have several adverse effects on the environment:
- Pollution: Empty cartridges contain residual e-liquid and nicotine, which can leach into soil and contaminate water sources.
- Wildlife Hazards: Animals may ingest the cartridges, mistaking them for food, leading to nicotine poisoning or physical harm.
- Landfill Accumulation: Disposable cartridges contribute to the growing problem of electronic waste in landfills, taking up space and releasing harmful chemicals over time.
Safety Precaution: Avoiding Leaks
Leaking e-liquid is not only messy but can also damage your device and waste precious juice. Here are some tips to avoid leaks:
8. Use a high-quality e-liquid
Low-quality e-liquids are more likely to leak because they are thinner and contain more impurities. Look for e-liquids that are made with high-quality ingredients and are free of PG (propylene glycol).
Here’s a table summarizing the key points:
| Tip | Explanation |
|---|---|
| Use a high-quality e-liquid | Low-quality e-liquids are more likely to leak because they are thinner and contain more impurities. |
| Use the right amount of e-liquid | Overfilling your tank can lead to leaking. |
| Prime your coil before vaping | This helps to ensure that the coil is fully saturated with e-liquid, which reduces the chance of leaking. |
| Store your vape in an upright position | Storing your vape on its side can cause e-liquid to leak out of the airflow holes. |
| Check your O-rings regularly | O-rings can wear out over time, which can lead to leaking. |
| Clean your vape regularly | E-liquid residue can build up over time and cause leaking. |
Troubleshooting: Addressing Common Issues
9. Weak Puffs or No Vapor
This issue can have several causes:
-
Weak battery: Check the battery level. If it’s low, fully charge the device.
-
Clogged wick: Remove the mouthpiece and gently blow on the bottom of the cartridge to dislodge any debris or e-liquid that may be blocking the wick.
-
Burnt coil: If the coil has been used extensively, it may have worn out and need to be replaced.
-
Incorrect resistance: Ensure that the Geek Bar Pulse cartridge is compatible with the battery. Incompatible resistance can lead to weak puffs or no vapor production.
-
Loose connection: Inspect the connection between the cartridge and the battery. Clean the contact points with a cotton swab and alcohol to ensure a secure fit.
-
Airflow blockage: The airflow holes may be clogged with e-liquid or condensation. Gently wipe them with a tissue or cotton swab to clear any obstructions.
-
Insufficient e-liquid: Check the e-liquid level in the cartridge. If it’s low, refill the device according to the instructions provided in the Refill Geek Bar Pulse section.
-
Faulty cartridge: If all the above troubleshooting steps have been performed and the issue persists, the cartridge may be faulty. Contact the manufacturer for assistance.
Removing the Rubber Stopper
Gently pull the rubber stopper out of the bottom of the Geek Bar Pulse. Be careful not to tear the rubber or the device.
Inserting the Needle
Insert the needle of the syringe into the hole in the rubber stopper. Make sure the needle is inserted all the way into the hole, but not so far that it touches the bottom of the device.
Filling the Device
Slowly inject the e-liquid into the device. Do not overfill the device, as this can cause leaking.
Reattaching the Rubber Stopper
Once the device is filled, reattach the rubber stopper to the bottom of the device. Press firmly to ensure that the stopper is securely in place.
Enjoying Your Refreshed Geek Bar Pulse
Once the device is refilled, you can enjoy your refreshed Geek Bar Pulse. The e-liquid will be evenly distributed throughout the device, providing you with a consistent and satisfying vaping experience.
Additional Tips
- Use a sharp needle to ensure that the e-liquid flows smoothly into the device.
- Do not overfill the device, as this can cause leaking.
- If you experience any leaking, try reattaching the rubber stopper more securely.
- If you have any other questions, please refer to the Geek Bar Pulse user manual.
Frequently Asked Questions
| Question | Answer |
|---|---|
| Can I refill my Geek Bar Pulse more than once? | Yes, you can refill your Geek Bar Pulse multiple times. However, we recommend that you do not refill it more than 3-4 times, as this can damage the device. |
| What type of e-liquid should I use to refill my Geek Bar Pulse? | You can use any type of e-liquid to refill your Geek Bar Pulse. However, we recommend that you use a high-quality e-liquid that is specifically designed for vaping devices. |
| How often should I refill my Geek Bar Pulse? | The frequency with which you need to refill your Geek Bar Pulse will depend on how often you vape. If you vape frequently, you may need to refill it every few days. If you vape less frequently, you may only need to refill it once a week or two. |
How To Refill Geek Bar Pulse
The Geek Bar Pulse is a popular disposable vape device that has become increasingly popular in recent months. However, many people believe that it is not possible to refill the Geek Bar Pulse once it has been used up.
In this article, we will show you how to refill the Geek Bar Pulse using a few simple steps. Please note that this process is not officially supported by Geek Bar. However, it has been shown to work by many users. By following these steps, you can save money and extend the life of your Geek Bar Pulse.
People Also Ask About How To Refill Geek Bar Pulse
Can I Refill The Geek Bar Pulse?
Yes, you can refill the Geek Bar Pulse. However, it is not officially supported by Geek Bar. By following the steps in this article, you can refill the Geek Bar Pulse and save money.
How Many Times Can I Refill The Geek Bar Pulse?
You can refill the Geek Bar Pulse multiple times. However, the number of times that you can refill it will depend on how well you take care of it. If you are careful not to damage the device or the coil, you should be able to refill it several times.
What Kind Of E-Liquid Can I Use To Refill The Geek Bar Pulse?
You can use any type of e-liquid to refill the Geek Bar Pulse. However, we recommend using a e-liquid that has a high VG content. This will help to prevent the coil from burning out quickly.
