Have you ever wondered how to remove the PUR filter from your pitcher? It’s a simple process that takes just a few minutes. In this article, we’ll walk you through the steps on how to do it. We’ll also provide some tips on how to keep your PUR filter clean and functioning properly. Read on to learn more!
First, you’ll need to locate the filter housing. It’s usually located at the bottom of the pitcher. Once you’ve found the filter housing, grip it firmly and turn it counterclockwise to remove it. Be careful not to spill any water when you do this. Once the filter housing is removed, you’ll see the PUR filter inside. To remove the filter, simply pull it straight up. You may need to use a little force, but it should come out easily.
Now that you’ve removed the PUR filter, it’s time to clean it. You can do this by rinsing it under running water. Be sure to remove any dirt or debris that may have accumulated on the filter. Once the filter is clean, you can reinstall it in the pitcher. To do this, simply insert the filter into the filter housing and turn it clockwise to tighten it. That’s all there is to it! Now you know how to remove and clean a PUR filter.
Safety Precautions
Gather Necessary Tools:
Before tackling the task, ensure you have everything you need within reach. You’ll require a clean washcloth or paper towels, a sink, and possibly a wrench (if your pitcher has a removable filter lid). Gather these tools beforehand to avoid unnecessary interruptions during the cleaning process.
Turn Off Water and Unplug Pitcher:
To prevent water spillage and ensure electrical safety, turn off the water supply to the pitcher and unplug it from any electrical outlet. This essential step minimizes the risk of accidents and allows you to focus on the task at hand without distractions.
Disconnect Filter Housing:
Locate the filter housing, which is typically at the top of the pitcher. In most models, it has a lid or cover that can be detached by hand or with a wrench. If using a wrench, proceed with caution to avoid damaging the housing. Once separated, set the filter housing aside for further cleaning.
Remove the Old Filter:
After disconnecting the filter housing, grasp the old filter and gently pull it straight up and out. Be careful not to squeeze or crush the filter as it may release activated carbon or other materials into the water. Dispose of the old filter responsibly according to the manufacturer’s instructions.
Identifying the Filter
**1. Check the Manual:**
Refer to the instruction manual that came with your PUR pitcher. It should provide clear instructions on how to locate and remove the filter.
**2. Locate the Filter Compartment:**
Most PUR pitchers have a separate compartment for the filter. Look for a clear plastic or gray cylindrical shape at the bottom of the pitcher. This compartment should be removable or easily accessible to allow for filter replacement.
| PUR Pitcher Model | Filter Compartment Location |
|---|---|
| Classic | Bottom of pitcher, accessible by unscrewing the base |
| Ultimate | Removable compartment at the bottom of the pitcher |
| Advanced | Gray cylindrical compartment visible from the side of the pitcher |
**3. Insert Your Finger into the Compartment:**
Once you have identified the filter compartment, gently insert your finger into it. You should feel a small hole or indentation on the filter’s surface.
Grasping the Filter
To remove the Pur filter from the pitcher, you will need to grasp it firmly. The filter is located at the bottom of the pitcher, and it is held in place by a plastic ring. To grasp the filter, reach your hand into the pitcher and feel for the plastic ring. Once you have found the ring, grip it firmly and pull it up and out of the pitcher. This will release the filter and allow you to remove it from the pitcher.
Here are some additional tips for grasping the filter:
- Make sure that your hands are clean before you reach into the pitcher.
- If the filter is stuck, you can try using a pair of pliers or a wrench to grip it.
- Be careful not to damage the filter when you are removing it.
Pulling the Filter
To remove the PUR filter from your pitcher, you will need to:
- Locate the filter release button. It is usually located on the bottom of the pitcher, near the handle.
- Press and hold the filter release button. This will release the filter from the pitcher.
- Pull the filter straight up and out of the pitcher. Be careful not to spill any water.
- Dispose of the old filter. You can recycle the filter by following the instructions on the package.
- Insert a new filter into the pitcher. Make sure that the filter is inserted all the way into the pitcher and that it is snapped into place.
- Fill the pitcher with water. Allow the water to filter through the filter before drinking it.
Additional tips for pulling the filter:
| Tip | Description |
|---|---|
| If the filter is stuck, you can try using a pair of pliers to pull it out. | Be careful not to damage the filter or the pitcher. |
| You can also try running hot water over the filter to loosen it up. | Be careful not to get the water too hot, as it could damage the filter. |
| If you are still having trouble removing the filter, you can contact PUR customer service for help. | They will be able to provide you with further instructions or send you a replacement filter. |
Inspecting the Filter
To inspect the filter, follow these steps:
- Remove the filter from the pitcher.
- Inspect the filter for any visible damage or discoloration. If the filter is damaged or discolored, it should be replaced.
- Run water over the filter for a few seconds to remove any loose particles.
- Hold the filter up to a light source and look for any cracks or holes in the filter media. If there are any cracks or holes, the filter should be replaced.
- Check the expiration date on the filter. If the filter has expired, it should be replaced.
Table 1: Filter Inspection Criteria
| Criteria | Inspection Method |
|---|---|
| Physical damage | Visual inspection |
| Discoloration | Visual inspection |
| Loose particles | Run water over the filter |
| Cracks or holes | Hold up to a light source |
| Expiration date | Check the filter packaging |
Cleaning the Filter Housing
The filter housing is the part of the pitcher that holds the filter. It is important to clean the filter housing regularly to prevent the build-up of bacteria and other contaminants. To clean the filter housing, follow these steps:
- Remove the filter from the pitcher.
- Fill the pitcher with warm water.
- Add a few drops of dish soap to the water.
- Swirl the water around in the pitcher to dislodge any dirt or debris.
- Rinse the pitcher thoroughly with clean water.
- Allow the pitcher to air dry completely before using it again.
Here is a more detailed guide to cleaning the filter housing:
| Step | Instructions |
|---|---|
| 1 | Remove the filter from the pitcher. |
| 2 | Fill the pitcher with warm water. |
| 3 | Add a few drops of dish soap to the water. |
| 4 | Swirl the water around in the pitcher to dislodge any dirt or debris. |
| 5 | Rinse the pitcher thoroughly with clean water. |
| 6 | Use a soft brush to clean the inside of the filter housing. Be sure to get into all the nooks and crannies. |
| 7 | Rinse the filter housing thoroughly with clean water. |
| 8 | Allow the pitcher to air dry completely before using it again. |
Replacing the Filter
To maintain optimal filtration performance, it’s crucial to replace the PUR filter according to the manufacturer’s recommended guidelines, typically every two to three months. Replacing the filter is a simple and straightforward process that can be completed in just a few easy steps:
1. Remove the Lid:
Unhinge or remove the top lid of the pitcher to access the filter.
2. Grasp the Filter:
Locate the filter inside the pitcher and gently grasp it with your hand.
3. Pull the Filter Out:
Carefully pull the filter straight up and out of the pitcher.
4. Inspect the Filter:
Before installing a new filter, inspect the old one for any signs of damage or discoloration that may indicate the need for more frequent replacements.
5. Remove the New Filter from Packaging:
Unwrap the new filter from its packaging, taking care not to touch the filter’s membrane.
6. Insert the New Filter:
Align the new filter with the designated slot in the pitcher and gently push it down until it fits snugly.
7. Reset the Filter Indicator:
Depending on the specific PUR pitcher model you have, there may be a filter indicator that needs to be reset. Refer to the user manual for specific instructions on how to do it.
Starting the Filtration Process
Initiating the filtration process is a crucial step to ensure that your water is purified and safe for consumption. To begin, follow the steps below:
1. Prepare the Pitcher: Before inserting the filter, ensure the pitcher is clean and empty.
2. Soak the Filter: Submerge the PUR filter in cold water for 15 minutes. This will activate the filter and prepare it for use.
3. Insert the Filter: Press the filter firmly into the designated slot at the bottom of the pitcher. Ensure it fits securely.
4. Fill the Pitcher: Fill the pitcher with cold tap water, leaving about an inch of space at the top.
5. Prime the Filter: Allow the water to filter through the pitcher twice. Discard the first two filtrations as they may contain activated carbon particles.
6. Rinse the Filter: After priming the filter, fill the pitcher again and let the water filter through. This will rinse any remaining fine particles.
7. Discard Initial Filtrations: The first few glasses of filtered water may have a smoky appearance or a slight odor. Discard these initial filtrations until the water runs clear.
8. Regularly Replace the Filter: The PUR filter effectively removes contaminants for a limited period. Replace the filter every 2 months or 40 gallons of water to ensure optimal filtration performance.
| Filter Model | Replacement Frequency |
|---|---|
| PUR Classic | 2 months or 40 gallons |
| PUR Advanced | 2 months or 100 gallons |
| PUR Ultimate | 2 months or 150 gallons |
Troubleshooting Common Issues
9. No Water Flowing Through Filter
If you’re experiencing issues with water not flowing through your PUR filter, there are a few possible causes and solutions to consider:
| Cause | Solution |
|---|---|
| Airlock in the Filter | Remove the filter and shake it gently to release any trapped air. Reinstall and flush the filter for several minutes until water flows freely. |
| Clogged Filter | Replace the filter with a new one. |
| Debris in Water Supply | Check the incoming water supply for any sediment or debris that could be blocking the flow. Clean the water supply hose or faucet aerator if necessary. |
If you continue to experience issues with water flow, it may be due to a faulty pitcher or filter. Contact PUR customer support for further assistance.
Maintaining the Filter Pitcher
1. Replace the Filter Regularly
The Brita pitcher filter needs to be replaced every two months or after 40 gallons of use. The specific time frame may vary depending on the model of your pitcher and the quality of your water. To replace the filter, simply remove the old one by pulling it straight up and inserting the new one in its place.
2. Clean the Pitcher Regularly
It is important to clean the Brita pitcher regularly to prevent bacteria from growing. To clean the pitcher, simply disassemble it and wash all of the parts with warm, soapy water. You can also use a mild bleach solution to disinfect the pitcher.
3. Store the Pitcher Properly
When you are not using the Brita pitcher, it is important to store it properly to prevent contamination. Store the pitcher in a cool, dry place away from direct sunlight.
4. Use Cold Water
When filling the Brita pitcher, it is important to use cold water. Cold water will help to improve the filtration process and will also help to keep the filtered water cold.
5. Let the Water Filter
When you fill the Brita pitcher, allow the water to filter through the filter completely before drinking it. This will help to ensure that the water is clean and free of contaminants.
6. Use the Filtered Water Promptly
Once you have filtered water, it is important to use it promptly. Filtered water will start to lose its freshness after a few days, so it is best to use it within a week.
7. Keep the Pitcher Full
To keep the Brita pitcher filter working properly, it is important to keep the pitcher full. A full pitcher will help to prevent the filter from drying out and will also help to keep the filtered water cold.
8. Avoid Freezing the Pitcher
It is important to avoid freezing the Brita pitcher. Freezing the pitcher can damage the filter and the pitcher itself.
9. Avoid Microwaving the Pitcher
It is also important to avoid microwaving the Brita pitcher. Microwaving the pitcher can damage the plastic and the filter.
10. Troubleshooting Common Problems
| Problem | Solution |
|---|---|
| Water is not filtering through the filter | The filter may need to be replaced. |
| Water is leaking from the pitcher | The pitcher may be damaged. Contact Brita customer service for assistance. |
| Water tastes funny | The filter may need to be replaced. You may also need to clean the pitcher. |
How To Remove Pur Filter From Pitcher
To remove a PUR filter from a pitcher, follow these steps:
- Fill the pitcher with cold water and let it sit for 5 minutes.
- Invert the pitcher and shake it vigorously to loosen the filter.
- Grasp the filter and pull it straight up out of the pitcher.
- Rinse the filter under running water and discard the old filter.
- Insert a new filter into the pitcher and push it down until it snaps into place.
- Fill the pitcher with cold water and let it sit for 5 minutes before using.
