Free your Honda CR-V from the confines of a faulty rear door! This comprehensive guide will empower you to tackle this task with confidence, saving you a trip to the mechanic. Whether it’s a jammed lock, a broken hinge, or a dent that’s driving you nuts, this article will guide you through the process of removing the rear door on your 2006 Honda CR-V. Get ready to say goodbye to that pesky door and hello to a rejuvenated ride.
Before diving into the specifics, let’s gather the necessary tools: a Phillips head screwdriver, a flathead screwdriver, a socket wrench with an appropriate socket size, a door panel removal tool (or a flathead screwdriver wrapped in a cloth), and a pair of pliers. Safety first! Disconnect the negative terminal of your car battery to prevent any electrical mishaps. Now, let’s dive into the steps, ensuring a smooth removal process.
Begin by prying off the plastic cover near the door handle. This will expose the screws behind it. Armed with your trusty Phillips head screwdriver, remove these screws. Next, carefully detach the door panel by prying it from the bottom and gently pulling it upwards. You’ll encounter a few clips along the way, but don’t worry, they’re designed to pop off. Once the panel is free, detach the electrical connectors for the power window, door lock, and any other connected components. Finally, disconnect the Bowden cable from the door handle and locate the two bolts securing the door to the frame. Remove these bolts and carefully lift the door off its hinges. Congratulations! You’ve successfully removed the rear door from your 2006 Honda CR-V.
Materials Required
To ensure a smooth and efficient removal process, it is essential to gather the following materials:
-
Socket Wrench
A socket wrench with an assortment of sockets (typically 10mm and 12mm) is crucial for removing the bolts that hold the rear door in place.
-
Phillips Screwdriver
A Phillips screwdriver is necessary for disassembling the interior door panel. It is recommended to have a variety of Phillips head sizes to accommodate different screw types.
-
Flathead Screwdriver
A flathead screwdriver can be used to pry open the door panel and remove certain clips. It is important to use a plastic or nylon pry tool to avoid damaging the door panel.
-
Torx Bit Socket
For some models of the 2006 Honda CR-V, a Torx bit socket may be required to remove screws hidden behind the door handle.
-
Plastic Spudger or Pry Tool
A plastic spudger or pry tool is a specialized tool designed to gently separate panels and remove clips without causing damage.
-
Clean Rags or Towels
Clean rags or towels are essential for wiping away dirt and debris during the removal process, as well as for protecting the door panel and other components from scratches.
-
Flashlight or Work Light
A flashlight or work light can be helpful for illuminating dark areas and ensuring that all bolts and screws are located and removed.
Safety Precautions
Before beginning any repairs on your vehicle, it is important to take the necessary safety precautions to ensure your safety and prevent injury. Follow these steps to properly prepare before starting the removal process:
1. Park on a Level and Stable Surface
Park your Honda CR-V on a level and stable surface, such as a driveway or parking lot. Engage the parking brake to prevent the vehicle from rolling.
2. Disconnect the Battery
Locate the negative battery terminal on your Honda CR-V, which is typically identified by a black cover with a negative (-) sign. Using a wrench or socket, carefully loosen the nut that secures the terminal and remove the cable. Be cautious not to short-circuit the terminal by touching it to any metal surfaces.
3. Gather Necessary Tools
Ensure you have all the necessary tools for the job, including a socket wrench, screwdriver, and pry tool. Consider wearing safety glasses to protect your eyes from debris.
4. Wear Appropriate Clothing
Wear appropriate clothing for the task, such as gloves and work boots, to protect yourself from any sharp edges or falling objects.
5. Allow the Vehicle to Cool Down
If you have recently driven your Honda CR-V, allow it to cool down before starting the repair. This will prevent burns from hot components.
Removing the Trim Panel
Step 1: Remove the Screws
Locate and remove two screws situated at the bottom corners of the door panel, using a Phillips head screwdriver.
Step 2: Disconnect the Electrical Connectors
Gently pull the door panel away from the door enough to access the electrical connectors. Disconnect the connectors for the window switch, door lock switch, and other electronic components.
Step 3: Removing the Panel
Locate the plastic clips that secure the door panel to the door frame. Using a trim removal tool or a flathead screwdriver, carefully pry around the perimeter of the door panel, releasing the clips one by one. Avoid using excessive force to prevent damage to the panel or the clips.
Step 4: Lift the Panel Off
Once all clips are released, carefully lift the door panel up and away from the door frame. Handle the panel with care to avoid breaking any tabs or components.
Step 5: Disconnect Remaining Connectors
If there are any remaining electrical connectors that were not disconnected earlier, unplug them now. Ensure that all connectors are completely detached to prevent damage during removal and reinstallation.
Disconnecting the Wiring Harness
Removing the rear door wiring harness is crucial for complete door removal. Follow these steps to disconnect it safely:
1. Locate the Wiring Harness Connect
The wiring harness connector is typically located near the hinge area of the door. Look for a black or gray plastic housing containing multiple wires.
2. Depress the Lock Tab
Most connectors have a lock tab that prevents accidental disconnection. Press the tab firmly to release the wires.
3. Disconnect the Pins
Use a small flat-head screwdriver or your fingernail to gently pry the pins out of the connector. Be careful not to damage the pins or wires.
4. Label and Secure the Wires
To avoid confusion when reconnecting, label the wires with tape or tags. Use electrical tape to secure any exposed wire ends to prevent short circuits.
Consider using a wire diagram or taking a photograph of the connector before disconnecting to ensure proper reassembly.
Removing the Door Lock Cylinder
The door lock cylinder is a small, cylindrical device that allows you to lock and unlock your door with a key. It is located on the inside of the door handle, and it is held in place by a set screw. To remove the door lock cylinder, follow these steps:
- Remove the door panel.
- Locate the door lock cylinder. It is located on the inside of the door handle, and it is held in place by a set screw.
- Loosen the set screw. Use a Phillips head screwdriver to loosen the set screw that is holding the door lock cylinder in place.
- Pull out the door lock cylinder. Once the set screw is loose, you can pull out the door lock cylinder.
- Disconnect the electrical connector. The door lock cylinder is connected to an electrical connector. Disconnect the electrical connector by pressing on the release tab and pulling the connector apart.
- Remove the door lock cylinder. Once the electrical connector is disconnected, you can remove the door lock cylinder by pulling it out of the door.
Note:
When removing the door lock cylinder, be careful not to damage the electrical connector. If the electrical connector is damaged, you will need to replace it.
Loosening the Hinge Bolts
To loosen the hinge bolts, you’ll need to locate them on the side of the door where the door attaches to the frame of the vehicle. There are usually two or three bolts per hinge, and they are typically 10mm or 12mm in size. Once you have located the bolts, use a wrench or socket to loosen them. Do not remove the bolts completely at this point.
| Step | Description |
|---|---|
| 1 | Locate the hinge bolts on the side of the door where it attaches to the vehicle frame. |
| 2 | Use a wrench or socket to loosen the hinge bolts, but do not remove them completely. |
Once the bolts are loose, you can carefully lift the door up and away from the frame of the vehicle. It may be helpful to have someone assist you with this step, as the door can be heavy.
Once the door is detached from the frame, you can disconnect the electrical connectors and any other components that are attached to the door, such as the door handle or window motor. Once everything is disconnected, you can remove the door from the vehicle.
Removing the Door
1. Gather Your Tools: You will need a socket wrench, a Phillips head screwdriver, a flat head screwdriver, and a pry bar or a flathead screwdriver.
2. Open the Door: Fully open the rear door that you are removing.
3. Remove the Door Panel: Use a Phillips head screwdriver to remove the screws located around the edges of the door panel. Carefully pry the panel off using a flat head screwdriver or a pry bar.
4. Disconnect the Electrical Connectors: Locate the electrical connectors attached to the door panel and disconnect them.
5. Remove the Bolts Holding the Door: Use a socket wrench to remove the bolts holding the door to the body of the vehicle.
6. Support the Door: Use a jack or a block of wood to support the door as you remove it from the body.
7. Remove the Door: Carefully lift the door off the body of the vehicle. Be careful not to damage the door or the body. The door is heavy, so it is recommended to have someone assist you in removing it.
Additional Notes for Step 7:
| Bolt Location | Bolt Size | Quantity |
|---|---|---|
| Top hinge | 14 mm | 2 |
| Middle hinge | 17 mm | 2 |
| Bottom hinge | 19 mm | 2 |
Once the bolts are removed, carefully lift the door upwards and away from the body of the vehicle. Disconnect any remaining electrical connectors or wires.
Transferring the Components
Now that you’ve removed the door, it’s time to transfer the components from the old door to the new one. This includes the window, door handle, door lock, and speaker. Be sure to disconnect all of the electrical connectors before removing the components.
To remove the window, first remove the two bolts that secure the window regulator to the door. Then, carefully lift the window out of the door. To remove the door handle, first remove the two screws that secure the handle to the door. Then, pull the handle out of the door. To remove the door lock, first remove the two screws that secure the lock to the door. Then, pull the lock out of the door. To remove the speaker, first remove the four screws that secure the speaker to the door. Then, pull the speaker out of the door.
Once you’ve transferred all of the components to the new door, it’s time to reassemble the door. To do this, simply reverse the steps that you took to remove the door. Be sure to tighten all of the bolts and screws securely.
Here is a table summarizing the steps for transferring the components:
| Component | Removal steps |
|---|---|
| Window | Remove the two bolts that secure the window regulator to the door. Carefully lift the window out of the door. |
| Door handle | Remove the two screws that secure the handle to the door. Pull the handle out of the door. |
| Door lock | Remove the two screws that secure the lock to the door. Pull the lock out of the door. |
| Speaker | Remove the four screws that secure the speaker to the door. Pull the speaker out of the door. |
Reinstalling the Door
Once the door is removed, you can begin the reinstallation process. Before you do, inspect the door and the door frame for any damages. If you find any damages, repair them before continuing.
- Start by lifting the door into the door frame. Make sure that the door is aligned properly with the frame.
- Install the upper hinge bolts first. Tighten the bolts until they are snug.
- Next, install the lower hinge bolts. Again, tighten the bolts until they are snug.
- Once the door is securely fastened, adjust the door so that it opens and closes smoothly.
- If the door is not opening or closing properly, you may need to adjust the door hinges.
- To adjust the door hinges, loosen the hinge bolts slightly.
- Move the door in the direction that you need to adjust it.
- Tighten the hinge bolts.
- Test the door to make sure that it opens and closes smoothly.
- Repeat steps 7-9 if necessary.
- Once the door is adjusted properly, tighten the hinge bolts fully.
- Install the door panel.
- Connect the electrical connectors.
- Install the door handle and lock.
- Test the door to make sure that it opens and closes properly.
How To Remove Rear Door From 2006 Honda Crv
Removing the rear door from a 2006 Honda CRV can be a challenging task, but it is possible to do it yourself with the right tools and knowledge. Here are the steps involved in removing the rear door from a 2006 Honda CRV:
1. Gather the necessary tools. You will need a socket wrench, a Phillips head screwdriver, a flat head screwdriver, and a pry bar.
2. Open the rear door and remove the two bolts that are located at the bottom of the door.
3. Remove the two bolts that are located at the top of the door.
4. Remove the two bolts that are located at the back of the door.
5. Carefully lift the door up and off of the hinges.
6. Disconnect the electrical connectors that are located at the back of the door.
7. Remove the door from the vehicle.
People Also Ask About How To Remove Rear Door From 2006 Honda Crv
How long does it take to remove a rear door from a 2006 Honda CRV?
It should take about 30 minutes to remove the rear door from a 2006 Honda CRV.
What are the most common problems with rear doors on Honda CRVs?
The most common problems with rear doors on Honda CRVs are that they can become misaligned, making it difficult to open and close them properly. They can also become damaged in an accident, or they can rust over time.
How can I prevent problems with the rear doors on my Honda CRV?
You can prevent problems with the rear doors on your Honda CRV by keeping them clean and well-lubricated. You should also avoid overloading the doors with heavy objects, and you should be careful not to damage them when opening and closing them.
