Replacing the ignition switch on a 2015 Dart SXT can be a daunting task, but it is possible to do it yourself with the right tools and knowledge. Here is a step-by-step guide for replacing the ignition switch on a 2015 Dart SXT.
Before embarking on this task, ensure you have all the necessary tools and replacement parts. Essential tools include a socket set, screwdrivers, and a torque wrench. Additionally, it is imperative to have a new ignition switch and key cylinder, as these are not reusable once removed. Additionally, consult your vehicle’s service manual for specific instructions and torque specifications for your particular model.
The process begins with disconnecting the battery to prevent any electrical hazards. Subsequently, you must remove the steering wheel, steering column shroud, and airbag. Carefully follow the instructions in the service manual to ensure safety and avoid damaging any components. Once these components are removed, you can access the ignition switch and its mounting bolts. Disconnect the electrical connectors and unscrew the bolts to release the faulty ignition switch. Finally, install the new ignition switch, reassemble all the components, and reconnect the battery. Remember to torque all bolts to the specified values and test the ignition switch before putting everything back together.
Reassembling the Steering Wheel and Airbag
Step 5: Reconnecting the Wires and Horn Spring
Locate the yellow and green wire connectors on the steering wheel and connect them to the corresponding connectors on the steering column. Ensure they are securely fastened.
Next, align the horn spring with the notches on the steering column and push it down. This will connect the horn button to the electrical system.
Step 6: Installing the Airbag Assembly
Carefully handle the airbag assembly and align it with the mounting bracket on the steering wheel. Verify that the alignment pins on the airbag fit into the corresponding holes on the bracket.
Apply gentle pressure to the airbag assembly to seat it properly. You may need to use a small tool, such as a plastic pry bar, to carefully lever it into place.
Once the airbag is seated, use the Torx screws to tighten the bolts that secure the assembly to the steering wheel. Ensure they are adequately tightened, but avoid overtightening.
| Bolt Size | Torque |
|---|---|
| M8 | 10 Nm |
How to Replace Ignition Switch Dart 2015 SXT
Replacing the ignition switch in a 2015 Dodge Dart SXT requires some mechanical knowledge and safety precautions. Here’s a step-by-step guide to assist you with the process:
- Gather Tools and Materials: You’ll need a set of screwdrivers, a Torx bit set, a steering wheel puller, a new ignition switch, and safety glasses.
- Disconnect the Battery: To prevent electrical hazards, disconnect the negative terminal of the car battery.
- Remove the Airbag Module: Use a Torx bit to remove the screws holding the airbag module in place. Carefully detach the airbag connector and set it aside.
- Detach the Steering Wheel: Using a steering wheel puller, detach the steering wheel from the steering column.
- Remove the Ignition Switch Cover: Locate the ignition switch cover and use a screwdriver to remove the screws holding it in place. Lift off the cover to expose the ignition switch.
- Disconnect the Ignition Switch Connectors: Carefully disconnect the electrical connectors plugged into the ignition switch.
- Remove the Ignition Switch: Use a screwdriver or a Torx bit (depending on your model) to remove the bolts securing the ignition switch to the steering column. Pull the switch straight out of the column.
- Install the New Ignition Switch: Align the new ignition switch with the steering column and insert it. Secure it with the bolts you removed earlier.
- Reconnect the Electrical Connectors: Plug the electrical connectors back into the ignition switch.
- Reattach the Ignition Switch Cover: Replace the ignition switch cover and secure it with the screws.
- Remount the Steering Wheel: Position the steering wheel onto the steering column and use the steering wheel puller to tighten it.
- Install the Airbag Module: Connect the airbag connector and carefully place the airbag module back in its position. Secure it with the Torx screws.
- Reconnect the Battery: Reattach the negative terminal to the car battery.
Note: It’s recommended to consult your vehicle’s service manual for specific instructions and safety precautions.
People Also Ask
How much does it cost to replace an ignition switch on a Dodge Dart?
The cost to replace an ignition switch on a Dodge Dart varies depending on your location, the type of switch required, and whether you do it yourself or hire a mechanic. On average, you can expect to pay between $200 and $500 for the parts and labor.
What are the symptoms of a bad ignition switch?
- Difficulty starting the car
- Engine stalling while driving
- Intermittent electrical issues
- Dashboard warning lights illuminating
How do I know if my Dodge Dart has a push-button start?
If your Dodge Dart has a push-button start, there will be a “Start” button located on the center console or dashboard. You’ll also have a key fob that you use to unlock the car and start the engine.
