If your Samsung fridge’s filter light is blinking, it’s time to replace the water filter. Replacing the filter is a quick and easy process that only takes a few minutes. However, before you can replace the filter, you’ll need to reset the filter light. Here’s how to do it:
Locate the water filter reset button. On most Samsung fridges, the reset button is located on the front of the fridge, near the water dispenser. The button may be labeled “Filter Reset” or “Filter Indicator.”
If you can’t find the reset button on the front of the fridge, consult your fridge’s user manual.
Press and hold the reset button for 5 seconds. The filter light will turn off, indicating that the filter has been reset.
Once you’ve reset the filter light, you can replace the water filter. To do this, simply remove the old filter and insert the new filter into the housing. Make sure to push the filter into place until it clicks.
Once the new filter is in place, press and hold the water dispenser button for 5 seconds. This will flush the water lines and remove any air that may be trapped in the system.
Resetting the Filter Light on a Samsung French Door Refrigerator
If the filter light on your Samsung French Door refrigerator is illuminated, it indicates that the water filter needs to be replaced. Here’s a detailed guide on how to reset the filter light after replacing the water filter:
Materials you’ll need:
- New water filter
Instructions:
1.
Locate and Remove the Old Filter
- Open the refrigerator door and locate the water filter housing, which is usually situated on the top or bottom grille inside the refrigerator compartment.
- Quarter-turn the filter housing counterclockwise to unlock it.
- Grasp the filter and pull it straight down to detach it from the housing.
2.
Insert the New Filter
- Remove any protective packaging from the new water filter.
- Align the notch on the new filter with the corresponding groove in the housing.
- Push the new filter up into the housing until it clicks into place.
3.
Reset the Filter Light
- Close the refrigerator door.
- Locate the “Filter Reset” button on the control panel. It may be labeled with a small water drop or “Filter.”
- Press and hold the “Filter Reset” button for three seconds, or until the filter light turns off.
Note: The reset process may vary slightly depending on the specific model of your Samsung French Door refrigerator. Refer to your user manual for more specific instructions.
How to Reset the Filter Light on a Samsung Top-Freezer Refrigerator
If the filter light on your Samsung top-freezer refrigerator is lit, it means that the water filter needs to be replaced. You can reset the filter light once you have replaced the filter by following these steps:
- Locate the water filter reset button. On most Samsung top-freezer refrigerators, the reset button is located on the bottom left-hand side of the interior of the refrigerator compartment, right next to the water filter housing.
- Press and hold the water filter reset button for 5 seconds.
- The filter light should now be reset.
Troubleshooting
If you have followed the steps above and the filter light is still lit, there may be a problem with the water filter or the reset button. Here are a few troubleshooting tips:
- Make sure that the water filter is properly installed. Remove the old filter and insert the new filter into the housing, making sure that it is fully seated.
- Make sure that the reset button is working properly. Try pressing the button several times to see if it clicks. If the button does not click, it may need to be replaced.
- If you have tried all of the above troubleshooting tips and the filter light is still lit, you may need to call a qualified appliance repair technician.
| Filter Light | Meaning |
|---|---|
| Green | The water filter is new and does not need to be replaced. |
| Yellow | The water filter is approaching the end of its life and needs to be replaced soon. |
| Red | The water filter is overdue for replacement. |
Troubleshooting the Filter Light on a Samsung Refrigerator
1. Check the Water Filter
The most common reason for the filter light to turn on is that the water filter needs to be replaced. Open the refrigerator door and locate the water filter compartment. Remove the old filter and insert a new one, making sure to tighten it securely.
2. Reset the Filter Indicator
Once you have replaced the filter, you need to reset the filter indicator. Locate the “Filter Reset” button on the refrigerator’s display panel or inside the fridge compartment. Press and hold the button for 3-5 seconds to reset the indicator.
3. Clean the Water Inlet Valve
If replacing the filter and resetting the indicator doesn’t turn off the light, the water inlet valve may be clogged. Disconnect the refrigerator from power, turn off the water supply, and remove the water inlet valve from the refrigerator. Clean the valve with a small brush and reinstall it.
4. Test the Water Dispenser
If the filter light remains on, test the water dispenser to ensure it’s working properly. Press the water dispenser button and observe the water flow. If the water isn’t flowing or is flowing slowly, there may be a blockage in the water line.
5. Advanced Troubleshooting
If the above steps don’t resolve the issue, you may need to perform advanced troubleshooting:
- Check the Control Board: Disconnect the refrigerator from power and remove the control board. Inspect the board for any loose connections or damaged components.
- Check the Wiring: Inspect the wiring harness for any damaged or disconnected wires. Ensure that all connections are secure.
- Contact Samsung Support: If all else fails, contact Samsung customer support for further assistance.
Clearing the Filter Light on a Samsung Refrigerator Model RF28R7551SG
1. Locate the Water Filter
The water filter is typically located on the top or bottom right-hand side of the refrigerator. It has a blue cap and a handle.
2. Remove the Water Filter
Grip the handle and pull the filter straight down. It may take some force to remove it.
3. Reset the Filter Indicator
Press and hold the “Filter Reset” button for 3 seconds. The filter light will turn off.
4. Reinstall the Water Filter
Push the filter back into the refrigerator until it clicks into place. Make sure it is securely seated.
5. Run Cold Water
Dispense cold water from the dispenser for about 2 minutes to flush the new filter.
6. Advanced Instructions for Samsung Refrigerator Model RF28R7551SG
- Navigate to the “Settings” menu on the refrigerator’s display.
- Select “Filter Status” or “Maintenance” from the menu.
- Locate the “Reset Filter” option and press “OK” or “Confirm.”
- The filter light will turn off, indicating the reset is complete.
Note: Make sure to replace the water filter every 6 months or as recommended by the manufacturer to ensure optimal water quality and prevent the buildup of impurities.
Resetting the Water Filter Indicator on a Samsung Refrigerator Model RF260BEAESR
1. Locate the Water Filter Reset Button:
Open the refrigerator door and locate the “Water Filter Reset” button. It is typically found on the dispenser panel.
2. Press and Hold the Button:
Press and hold the “Water Filter Reset” button for 3 seconds. The indicator light will start to flash.
3. Release the Button and Wait:
Release the button and wait for the indicator light to turn off. This may take a few seconds.
4. Confirm the Reset:
Open and close the refrigerator door to confirm that the indicator light has been reset.
5. Considerations for Different Models:
The location and steps for resetting the water filter indicator may vary slightly for different Samsung refrigerator models. Consult your user manual for specific instructions.
6. Resetting Without a Reset Button:
If your refrigerator does not have a “Water Filter Reset” button, you can still reset the indicator by unplugging the refrigerator for 10 seconds. This will reset all electronic settings.
7. Detailed Troubleshooting for Resetting Issues:
– Indicator light stays on after reset: Ensure the filter is firmly seated in the housing. Unplug the refrigerator for 2 minutes and plug it back in. If the issue persists, contact Samsung support.
– Indicator light does not turn off after 10 minutes: Replace the water filter with a new one. If the issue persists, contact Samsung support.
– Indicator light flashes rapidly: There may be an issue with the water dispenser system. Contact Samsung support for assistance.
– Indicator light flashes intermittently: Check the water line connections to ensure they are secure. If the issue persists, contact Samsung support.
Opening the Control Panel
Locate the control panel on your Samsung refrigerator. It is typically located on the front of the fridge, near the top. Pull the handle or press the button to open the control panel.
Locating the Filter Reset Button
Once the control panel is open, look for the filter reset button. It is usually a small, round button with the word “Filter” or “Reset” labeled on it.
Pressing the Filter Reset Button
Press and hold the filter reset button for approximately 3 seconds. The filter light should begin to flash.
Releasing the Filter Reset Button
Release the filter reset button when the filter light starts to flash. The filter light should turn off after a few seconds.
Confirming the Reset
Press and hold the filter reset button again for approximately 1 second. The filter light should turn back on, indicating that the reset has been successful.
Closing the Control Panel
Close the control panel by pushing it back into place or pressing the button to lock it shut.
Resetting the Filter Light on a Samsung Refrigerator Model RF23M8070SR
The steps for resetting the filter light on a Samsung refrigerator model RF23M8070SR are as follows:
| Step | Action |
|---|---|
| 1 | Locate the control panel on the front of the fridge. |
| 2 | Open the control panel. |
| 3 | Locate the filter reset button. |
| 4 | Press and hold the filter reset button for approximately 3 seconds. |
| 5 | Release the filter reset button. |
| 6 | Press and hold the filter reset button again for approximately 1 second. |
| 7 | Close the control panel. |
Understanding the Filter Light on Samsung Refrigerators
The filter light on Samsung refrigerators is an indicator that lets you know when it’s time to replace the water filter.
How to Reset the Filter Light on Samsung Refrigerators
- Locate the Filter Reset button.
- Press and hold the Filter Reset button for 3 seconds.
- The filter light will turn off.
Additional Notes:
The filter light will also turn off automatically after 6 months, even if the filter has not been replaced.
If the filter light continues to blink after you have reset it, there may be a problem with the filter or the refrigerator.
You can find more information about resetting the filter light in your refrigerator’s user manual.
| Refrigerator Model | Filter Reset Button Location |
|---|---|
| RF28R7351SR | Inside the refrigerator, on the right-hand wall |
| RF23J9011SR | On the front of the refrigerator, below the display panel |
How To Reset Filter Light On Samsung Fridge
1. Locate the filter reset button on the front of the refrigerator. It is usually located near the water dispenser or ice maker.
2. Press and hold the filter reset button for 3 seconds. The filter light will turn off.
People Also Ask
How often should I reset the filter light on my Samsung fridge?
You should reset the filter light every 6 months, or when the filter indicator light turns on.
What happens if I don’t reset the filter light on my Samsung fridge?
If you don’t reset the filter light, the fridge will eventually stop dispensing water and ice.
