The Anycubic Saturn 4 Ultra is a new resin 3D printer that boasts a number of impressive features, including a large build volume, high resolution, and fast print speeds. However, in order to get the most out of your Saturn 4 Ultra, it is important to properly calibrate the resin. This process may seem daunting, but it is actually quite simple. In this article, we will walk you through the steps on how to set up a resin calibration Saturn 4 Ultra.
The first step is to prepare your resin. Make sure that the resin is well-mixed and that there are no bubbles in the resin. Once the resin is prepared, you can pour it into the resin tank. The next step is to level the build plate. This is important to ensure that the prints adhere properly to the build plate. To level the build plate, simply loosen the screws on the build plate and then adjust the build plate until it is level. Once the build plate is level, you can tighten the screws.
The final step is to calibrate the resin. This is done by printing a series of test prints. The first test print is a small cube. The cube should be printed with a layer height of 0.05mm and an exposure time of 10 seconds. Once the cube is printed, you can measure the dimensions of the cube. The cube should measure 20mm x 20mm x 20mm. If the cube does not measure 20mm x 20mm x 20mm, then you need to adjust the exposure time. Once you have found the correct exposure time, you can print your final model.
How To Set Up A Resin Calibration Saturn 4 Ultra
The Saturn 4 Ultra is a top-of-the-line resin printer from Elegoo. It’s known for its high precision and fast printing speeds. However, in order to get the most out of your Saturn 4 Ultra, you need to properly calibrate the resin. Here’s how to do it:
Step 1: Gather your materials
You will need the following materials:
- A Saturn 4 Ultra printer
- A bottle of resin
- A build plate
- A spatula
- A set of Allen wrenches
**Step 2: Prepare the build plate**
The first step is to prepare the build plate. Clean the build plate with isopropyl alcohol and a lint-free cloth. Then, apply a thin layer of resin to the build plate. Use the spatula to spread the resin evenly over the surface of the build plate.
**Step 3: Install the build plate into the printer**
Once the build plate is prepared, it’s time to install it into the printer. Loosen the two screws on the front of the printer and lift the build plate into place. Tighten the screws to secure the build plate.
**Step 4: Calibrate the Z-axis**
The next step is to calibrate the Z-axis. This step ensures that the printer is properly leveled and that the build plate is at the correct height. To calibrate the Z-axis, follow these steps:
- Loosen the two screws on the back of the printer that hold the Z-axis motor in place.
- Turn the Z-axis motor by hand until the build plate just touches the top of the vat.
- Tighten the two screws to secure the Z-axis motor.
**Step 5: Calibrate the resin**
The final step is to calibrate the resin. This step ensures that the printer is using the correct amount of resin for each layer. To calibrate the resin, follow these steps:
- Print a test print using the default settings.
- Examine the test print. If the print is too thick, increase the exposure time. If the print is too thin, decrease the exposure time.
- Repeat steps 1 and 2 until the test print is the correct thickness.
People Also Ask About How To Set Up A Resin Calibration Saturn 4 Ultra
What is the difference between resin calibration and Z-axis calibration?
Resin calibration ensures that the printer is using the correct amount of resin for each layer, while Z-axis calibration ensures that the printer is properly leveled and that the build plate is at the correct height.
How often should I calibrate my resin printer?
You should calibrate your resin printer every time you change resins or if you notice that the quality of your prints has decreased.
Can I use any type of resin with my Saturn 4 Ultra?
No, you can only use resins that are specifically designed for the Saturn 4 Ultra. Using other types of resin can damage your printer.
