Taking apart a Selky Foam Cannon is an easy task that can be completed in just a few minutes. Foam cannons are used to apply a thick layer of foam to a vehicle’s surface, and they can be used for both personal and commercial purposes. If you’re having trouble getting your foam cannon to work properly, taking it apart and cleaning it may be the solution. In this article, we’ll walk you through the steps on how to take apart a Selky Foam Cannon.
First, you’ll need to gather a few tools. You’ll need a Phillips head screwdriver, a flathead screwdriver, and a pair of pliers. Once you have your tools, you can begin taking apart the foam cannon. Start by removing the two screws that hold the top of the foam cannon in place. Once the screws are removed, you can lift the top of the foam cannon off. Next, remove the two screws that hold the bottom of the foam cannon in place. Once the screws are removed, you can lift the bottom of the foam cannon off.
Now that the foam cannon is disassembled, you can clean the individual parts. Use a mild soap and water solution to clean the parts. Rinse the parts thoroughly with clean water and allow them to dry completely. Once the parts are dry, you can reassemble the foam cannon. Start by attaching the bottom of the foam cannon to the top of the foam cannon. Secure the two parts together with the two screws. Next, attach the top of the foam cannon to the bottom of the foam cannon. Secure the two parts together with the two screws. Finally, test the foam cannon to make sure it’s working properly.
Necessary Tools and Materials
To disassemble a Selky Foam Cannon, you will need the following tools and materials:
Basic Tools:
- Adjustable wrench or socket wrench: for removing the nozzle and fittings.
- Phillips head screwdriver: for removing the handle and other components.
- Flathead screwdriver: for prying apart certain components.
- Needle-nose pliers: for removing small parts and o-rings.
- Safety glasses: to protect your eyes from flying debris.
Specialized Tools (Optional):
- Torx wrench: for removing specialized fittings or bolts.
- Hose clamp pliers: for removing and installing hose clamps.
Materials:
- Towels or rags: for wiping up spills or excess sealant.
- Lubricant: for lubricating o-rings and other moving parts.
- Replacement parts (optional): if any components need to be replaced.
Tips for Gathering Tools:
- It is recommended to have a variety of wrench sizes available to accommodate different fittings.
- Make sure the screwdrivers you select have the appropriate sized tips for the screws you need to remove.
- Use a lubricant specifically designed for use with o-rings and other rubber components.
Step-by-Step Disassembly
Taking apart a Selky foam cannon is a simple process that can be completed in a few minutes. To disassemble the cannon, you will need the following tools:
- Phillips head screwdriver
- Flat head screwdriver
- Wrench
Step 1: Remove the Nozzle
Start by removing the nozzle from the cannon. To do this, use the wrench to loosen the nut that holds the nozzle in place. Once the nut is loose, you can remove the nozzle by hand.
Step 2: Remove the Head
Next, remove the head from the cannon. To do this, use the Phillips head screwdriver to remove the two screws that hold the head in place. Once the screws are removed, you can remove the head by hand.
Step 3: Remove the Body
To remove the body from the cannon, you will need to separate the two halves of the body. To do this, use the flat head screwdriver to pry apart the two halves. Once the two halves are separated, you can remove the body from the cannon.
| Part | Quantity |
|---|---|
| Nozzle | 1 |
| Head | 1 |
| Body | 2 |
| Trigger | 1 |
Step 4: Remove the Trigger
To remove the trigger from the cannon, you will need to use the flat head screwdriver to pry off the spring that holds the trigger in place. Once the spring is removed, you can remove the trigger by hand.
Removing the Bottle and Handle
To detach the bottle, grasp the handle firmly and pull it straight up. The bottle should come off with ease. If it is stuck, you can try twisting it gently back and forth while pulling.
Once the bottle is removed, you can proceed to detach the handle. To do this, locate the screws that are securing the handle to the body of the foam cannon. There are typically two or three screws, depending on the model. Use a screwdriver to remove the screws and then lift the handle off.
Here is a more detailed step-by-step guide to removing the bottle and handle:
| Step | Instructions |
|---|---|
| 1 | Grasp the handle firmly and pull it straight up to detach the bottle. |
| 2 | Locate the screws securing the handle to the body of the foam cannon. |
| 3 | Use a screwdriver to remove the screws. |
| 4 | Lift the handle off once the screws are removed. |
Detaching the Spray Nozzle
5. Removing the Spray Nozzle Cap
To remove the spray nozzle cap, grasp the plastic disc at the bottom of the nozzle and turn it counterclockwise. This will loosen the cap and allow you to pull it off the nozzle. Be careful not to lose the small rubber washer that is located inside the cap, as this washer helps to create a seal between the cap and the nozzle.
Once you have removed the cap, you can use a needle or a small pin to release the plastic clip that holds the spray nozzle in place. Once the clip is released, you can gently pull the spray nozzle away from the body of the foam cannon.
| Tips | |
|---|---|
| If you are having trouble removing the spray nozzle cap, you can try using a pair of pliers. However, be careful not to overtighten the pliers, as this could damage the cap. | |
| If you lose the small rubber washer that is located inside the spray nozzle cap, you can replace it with a new washer from a hardware store. |
| Step | Instructions |
|---|---|
| 1 | Fill a bucket with warm water and add a foaming cleaning solution or car wash soap. |
| 2 | Submerge the foam body in the solution and agitate it gently to dissolve the foam residue. |
| 3 | Rinse the foam body thoroughly with clean water to remove all cleaning solution. |
| 4 | Allow the foam body to air dry completely before reassembling the cannon. |
How To Take Apart A Selky Foam Cannon
Selky foam cannons are a great way to get a thick, foamy lather for your car wash. But if you’ve ever needed to take one apart, you know it can be a bit of a challenge. Here’s a step-by-step guide on how to do it:
- Remove the nozzle. The nozzle is the part of the foam cannon that sprays the foam. To remove it, simply unscrew it from the top of the cannon.
- Remove the filter. The filter is located inside the top of the foam cannon. To remove it, simply pull it out.
- Remove the body. The body of the foam cannon is the main part of the unit. To remove it, simply unscrew it from the bottom of the cannon.
- Remove the piston. The piston is located inside the body of the foam cannon. To remove it, simply pull it out.
- Remove the o-rings. The o-rings are located on the piston and the body of the foam cannon. To remove them, simply pull them off.
Once you’ve removed all of the parts, you can clean them with soap and water. Be sure to dry them thoroughly before reassembling the foam cannon.
People Also Ask About How To Take Apart A Selky Foam Cannon
How do I clean a Selky foam cannon?
To clean a Selky foam cannon, simply disassemble it and clean the parts with soap and water. Be sure to dry them thoroughly before reassembling the foam cannon.
How do I fix a Selky foam cannon that is not working?
If your Selky foam cannon is not working, there are a few things you can try:
- Check to make sure that the nozzle is not clogged.
- Check to make sure that the filter is not clogged.
- Check to make sure that the body of the foam cannon is not cracked or damaged.
- Check to make sure that the piston is not damaged.
- Check to make sure that the o-rings are not damaged.
If you find any damaged parts, you can replace them with new ones. You can find replacement parts for Selky foam cannons online or at your local hardware store.
How do I get more foam from my Selky foam cannon?
There are a few things you can do to get more foam from your Selky foam cannon:
- Use a higher-quality car wash soap.
- Add more soap to the foam cannon reservoir.
- Use a wider nozzle setting.
- Hold the foam cannon closer to the car.
- Move the foam cannon more slowly over the car.
