1. Guide on How to Snake Cable to Glovebox of 2020 Toyota Tacoma

Every vehicle, no matter its make or model, is likely to have some kind of utility glove compartment or storage space. This can present a problem if you wish to route a cable – such as an auxiliary or power cable – through the glove compartment. In this guide, we’ll show you a quick and easy way to snake a cable to the glovebox of your 2020 Toyota Tacoma.

We’ll start by removing the glove compartment entirely, since this will give us better access to the back of the opening. To do this, first, open the glove compartment and remove the two screws that are located on either side of the opening. Next, locate the two plastic tabs that are located at the bottom of the glove compartment and pull them inward. This will release the glove compartment from its housing, and you can now remove it.

Once the glove compartment is removed, you should be able to see a hole in the back of the opening. This is where the cable will enter the glove compartment. Take your cable and insert it into the hole, making sure that there is enough slack on the other side so that you can connect it to the desired device on the inside of the glove compartment. Once the cable is in place, you can re-install the glove compartment.

Identifying the Glovebox Location

The glovebox in the 2020 Toyota Tacoma is conveniently located on the passenger side of the vehicle. To access it, follow these steps:

Locate the small, rectangular panel on the lower left side of the dashboard.
Gently pull on the panel to release the glovebox door.
Open the glovebox by pulling down on the handle.

Once the glovebox is open, you will have access to its spacious interior, which can accommodate various items such as the vehicle’s owner’s manual, registration documents, and small personal belongings.

It’s worth noting that some trim levels of the 2020 Toyota Tacoma may feature a locking glovebox for added security. To lock the glovebox, simply insert the vehicle’s key into the lock cylinder located on the glovebox door and turn it clockwise.

Removing the Kick Panel

1. Locate the kick panel on the driver’s side of the vehicle. It is the plastic panel that covers the area below the steering wheel.
2. Remove the two screws that hold the kick panel in place. The screws are located at the top and bottom of the panel.
3. Carefully pull the kick panel away from the dashboard. It may be helpful to use a trim tool to gently pry the panel loose.
4. Locate the grommet that allows the wire harness to pass through the firewall. The grommet is a round rubber piece that is located behind the kick panel.

If there is no existing grommet, you will need to create one. To do this, use a sharp knife or a drill to make a hole in the firewall. The hole should be large enough to allow the wire harness to pass through.
Insert the wire harness through the grommet or the hole you created. Be sure to leave enough slack in the wire harness so that you can work with it easily.
5. Connect the wire harness to the back of the glovebox. The wire harness will likely have a connector that matches the connector on the back of the glovebox.
6. Secure the kick panel back into place. Be sure to tighten the screws securely.

Routing the Cable through the Firewall

The firewall, which separates the engine compartment from the cabin, is where you’ll need to route the cable. To do this, you’ll need to drill a small hole through it in a spot that won’t interfere with any cables or hoses that are already present. Before you start drilling, make sure you check both sides of the firewall to make sure there’s nothing behind it that you might accidentally hit.

Once you’ve found a suitable spot to drill the hole, use a sharp drill bit to make a hole that’s just large enough to fit the cable through. Be careful not to drill too large a hole, as this could weaken the firewall and create a safety hazard.

Once you’ve drilled the hole, you’ll need to feed the cable through it. To do this, use a piece of wire or a coat hanger to push the cable through the hole from the engine compartment side. Once the cable is pulled through, use a grommet or other sealant to seal the hole around the cable to prevent water and debris from entering the cabin.

Locating the Hole in the Firewall

There is a rubber grommet on the driver’s side of the firewall that is used for routing wires into the cabin. This grommet is located behind the brake booster and master cylinder. It is possible to route the cable through this grommet, but it is a tight fit. If you are unable to route the cable through the grommet, you can drill a small hole in the firewall next to the grommet.

Drilling the Hole in the Firewall

If you need to drill a hole in the firewall, use a sharp drill bit and drill a hole that is just large enough to fit the cable through. Be careful not to drill too large a hole, as this could weaken the firewall and create a safety hazard. Once you have drilled the hole, use a grommet or other sealant to seal the hole around the cable to prevent water and debris from entering the cabin.

Routing the Cable through the Grommet

If you are able to route the cable through the grommet, you will need to use a wire or coat hanger to push the cable through the grommet. Once the cable is pulled through, use a grommet or other sealant to seal the hole around the cable to prevent water and debris from entering the cabin.

Tips

Use a sharp drill bit and drill a hole that is just large enough to fit the cable through. Do not drill too large a hole, as this could weaken the firewall and create a safety hazard.
Use a grommet or other sealant to seal the hole around the cable to prevent water and debris from entering the cabin.
If you are unable to route the cable through the grommet, you can drill a small hole in the firewall next to the grommet.

Connecting the Cable to the Head Unit

Once you have connected the cable to the back of the glovebox, you will need to connect it to the head unit. Here are the steps on how to do this:

Locate the head unit in your Toyota Tacoma. It is usually located in the center of the dashboard.
Remove the faceplate of the head unit by gently pulling it towards you.
Locate the AUX input on the back of the head unit. It is usually denoted by a 3.5mm jack.
Plug the other end of the cable into the AUX input on the head unit.
Replace the faceplate of the head unit.
Turn on the head unit and select the AUX input.

Running the Cable to the Glovebox

Once you have connected the cable to the head unit, you will need to run it to the glovebox. Here are the steps on how to do this:

Open the glovebox.
Locate a small hole in the back of the glovebox. This hole is usually located near the bottom of the glovebox.
Feed the cable through the hole in the back of the glovebox.
Close the glovebox.

Reinstalling the Kick Panel

Once you’ve successfully snaked the cable through the firewall and into the glovebox, it’s time to reinstall the kick panel. Here’s how:

Align the kick panel with the dashboard.
Push the panel firmly into place until it snaps securely.
Locate the two screws that hold the kick panel in place.
Using a Phillips head screwdriver, tighten both screws.
Check that the kick panel is securely attached.
Inspect the area around the kick panel for any gaps or openings.
If necessary, adjust the kick panel or add some weatherstripping to seal any potential air leaks.

Locate Access Hole

Open the glovebox and locate the access hole on the back panel. This hole is usually covered by a rubber grommet or a plastic plug.

Remove Grommet or Plug

Remove the grommet or plug by prying it out with a small flathead screwdriver or a plastic trim removal tool.

Feed Cable Through Hole

Feed the cable through the access hole and into the glovebox.

Connect Cable to Device

Connect the cable to the desired device inside the glovebox, such as a phone or a charging adapter.

Secure Cable (Optional)

If desired, use cable ties or Velcro straps to secure the cable inside the glovebox and prevent it from moving around.

Reinstall Grommet or Plug

Replace the grommet or plug into the access hole to seal it and prevent dust or debris from entering the glovebox.

Troubleshooting Cable Issues

Lost or Missing Grommet or Plug

If the grommet or plug is lost or missing, you can use a piece of foam or rubber to plug the hole until you can get a replacement.

Cable Does Not Fit Through Hole

If the cable is too thick to fit through the hole, you may need to use a smaller cable or drill a larger hole.

Intermittent Connection

If you experience intermittent connection issues, check the cable connections at both ends and make sure the cable is not damaged.

Cannot Connect to Device

If you cannot connect the device to the cable, check the device’s compatibility with the cable and make sure the device is turned on.

Noise or Interference (For Audio/Video Cables)

If you experience noise or interference when using audio/video cables, try using a different cable or checking for loose connections.

How To Snake Cable To Glovebox in Toyota Tacoma 2020

To snake a cable to the glovebox in a Toyota Tacoma 2020, follow these steps:

Open the glovebox.
Locate the hole in the back of the glovebox. This hole is usually located on the left side of the glovebox, near the bottom.
Insert a fish tape or a stiff wire into the hole. Feed the fish tape or wire through the hole and out the other side of the glovebox.
Attach the cable to the fish tape or wire. Use electrical tape or a zip tie to secure the cable to the fish tape or wire.
Pull the fish tape or wire back through the hole, bringing the cable with it.
Connect the cable to the desired device in the glovebox.